Main Menu
Home
Branches
Development
Documentation
Downloads
Support
Affiliates
Testimonials

Search Web Pages




SourceForge
Summary
   Developers
   Statistics
File Releases
MediaWiki
Trac
IdeaTorrent
Mailing Lists
Git Repository

Support

How do I request help?

Q. If I want help troubleshooting a connectivity failure with my LEAF router, what information should I send?

A. The exact information needed will vary by what trouble needs shooting.

Before You Post

  • You should check the LEAF FAQs to see if your question has a stock answer.
  • You should subscribe to the leaf-user mailing list, since some people with helpful knowledge will reply only to the list.
  • You should search the list archives, to see if your question has already been asked and answered (the FAQs are not always as up-to-date as we wish they were).

Please remember we only know what is posted in your message. Do not leave out any information that appears to be correct, or was mentioned in a previous post. There have been countless posts by people who were sure that some part of their configuration was correct when it actually contained a small error. We tend to be skeptics where detail is lacking.

Please keep in mind that you're asking for free technical support. Any help we offer is an act of generosity, not an obligation. Try to make it easy for us to help you. Follow good, courteous practices in writing and formatting your e-mail. Provide details that we need if you expect good answers. Exact quoting of error messages, log entries, command output, and other output is better than a paraphrase or summary.

When asking for help with routing or firewalling questions, ALWAYS include this information:

  • the exact name of the LEAF distribution and version you are running.
  • the exact kernel version you are running
    ash# uname -a
  • the complete, exact output of
    ash# ip addr show
  • the complete, exact output of
    ash# ip route show
  • the exact wording of any ping failure responses, including the ping command itself (there are some FAQ entries to help you).

Depending on the specific problem, include some or all of:

  • the exact output of the command below is typically useful for NIC-related problems.
    ash# lsmod
  • the exact output of the commands below is typically useful for firewall-related problems.
         -EITHER- (kernel 2.2.x)
    ash# ipchains -nvL
    
         -OR- (kernel 2.4.x)
    
    ash# iptables -nvL
      -and-
    ash# iptables -t nat -nvL
    
         -OR- (if you use Shorewall)
    
    ash# /sbin/shorewall status
  • the exact output of the commands below is typically useful for port-forwarding problems.
         -EITHER- (kernel 2.2.x)
    ash# ipmasqadm mfw -nL
      -and-
    ash# ipmasqadm portfw -nL
    
         -OR- (kernel 2.4.x)
    
    ash# iptables -t nat -nvL
  • any messages from dhclient in your logs typically for the setup of DHCP-dynamic external connections.
  • any messages from ppp or pppoe in your logs typically for the setup of PPPoE-dynamic external connections.

This is not an exhaustive list; we've covered only the most common sorts of troubleshooting problems that we see. If you have a less common problem, or you use an ISP that does something unusual, you may need to provide other specifics to get good help.

As a general matter, please do not edit the diagnostic information in an attempt to conceal your IP address, netmask, nameserver addresses, domain name, etc. These aren't secrets, and concealing them often misleads us.

Passwords are the exception to this rule: Replace each password with the letter "x".

It isn't easy to post messages directly from a LEAF system, but it is easy to transfer diagnostic information to a floppy. Here is how you do this:

  1. Format a spare 1440KB MSDOS floppy as you normally would under DOS, Windows, or Linux. Your floppies are probably already formatted this way.
  2. Remove the LEAF floppy and insert the new floppy in its place.
  3. Mount the floppy on the LEAF system by running this command:
    ash# mount -t msdos /dev/fd0u1440 /mnt
  4. Use the appropriate command(s) from the list above to copy information to text files on the floppy. Examples:
    ash# cp /var/log/messages /mnt/messages.txt
    ash# ip addr show > /mnt/address.txt
    ash# ip route show > /mnt/route.txt
    ash# ipchains -nvL > /mnt/filter.txt
    ash# /usr/sbin/ipmasqadm mfw -nL > /mnt/mfw.txt
    ash# /usr/sbin/ipmasqadm portfw -nl > /mnt/portfw.txt
    ash# cat /proc/net/ip_masq/autofw > /mnt/autofw.txt
  5. Unmount the floppy by running this command:
    ash# umount /mnt
  6. Remove the floppy from your LEAF system.

At your workstation, open the files you have just put on your floppy and cut-and-paste them into a mailing-list e-mail. The details depend on the operating system and e-mail software you use, but we assume you are familiar with them.

  • Created on 2004-03-08 10:45:03 by mhnoyes
  • Updated on 2004-12-16 09:48:44 by mhnoyes

 Printable Version


What's Related

Hosted on Get LEAF Linux Embedded Appliance Framework at SourceForge.net. Fast, secure and Free Open Source software downloads, and powered by phpWebSite.